When Scott closes his eyes to stop the blast, you hear the delicate flutter of dust and debris literally falling from above and all around. Scott opens his eyes and his optic force blasts rip a trench into the bathroom wall and then upwards into the ceiling. A bully from the football team pounds on the stall door where Scott is hiding. About a minute later, Scott Summers, aka Cyclops, has run into the boys’ bathroom and is struggling to control his mutant powers. I heard a class-ending bell emanate from the upper right part of my room even though there were no speakers there. The oval design of of MartinLogan’s signature five-way speaker binding posts make tightening a breeze.Īt about the 9:21 mark, the scene has shifted to a high-school. My walls and speakers disappeared and I heard rocks fall from overhead as the stones and debris entombed Apocalypse. The Dolby Atmos mix created a superb sense of space. Guards collapse a pyramid with Apocalypse inside. During the scene in ancient Egypt where the X-Men’s nemesis Apocalypse is about to transfer his consciousness to another mutant, a revolt ensues. Well, it didn’t take long for my doubts to be erased.įiring up the Ultra-HD Blu-ray version of X-Men Apocalypse with its Dolby Atmos track put me on notice. Could these up-firing speakers really work and give my dedicated setup a run for its money? About a year an a half ago, I set up a Dolby Atmos, DTS:X and Auro-3D immersive audio setup in my basement with dedicated in-ceiling speakers. I’ll confess that I’ve been a bit skeptical of the Motion AFX speakers and Atmos-enabled speakers in general. I played a variety of Dolby Atmos and DTS:X sources and likewise used the Dolby Surround and DTS Neural:X up-mixers, which take a traditional 5.1 or 7.1 movie soundtrack and extract height information to play it with an immersive audio presentation. I could therefore switch between the two and hear any differences in an A-B scenario. The second input was configured for a traditional 5.1 setup and would decode the regular multi-channel Dolby or DTS surround mix. Using the AVM 60’s slick capability of loading multiple speaker profiles, I configured one input dedicated to a 5.1.4 Dolby Atmos and DTS:X setup. I used a high-end Anthem AVM 60 preamp processor, which can support both Dolby Atmos and DTS:X setups, along with an Oppo UltraHD Blu-ray player. I tested the Motion AFX in a room with a 9-foot ceiling as part of a Dolby Atmos and DTS:X 5.1.4 setup (five main speakers, one subwoofer, and four Motion AFX speakers). The only caveat is that the Motion AFX will look more like a rhombus when paired with non-MartinLogan Motion series speakers. The Motion AFX have an angled, parallelogram look to them and a high-gloss, piano-black finish that mates them perfectly to Martin Logan’s Motion series loudspeakers, although there’s nothing to prevent you from pairing them with any flat-top speaker. You can use spades, banana plugs, or bare wire. MartinLogan’s oval-shaped five-way binding posts are superb and easy to tighten. Therefore you always set the Motion AFX as a “small” speaker in your A/V receiver, though modern room correction systems typically take care of this for you automatically. Frequencies above 80Hz are directional, while frequencies below that are not. Indeed, the Motion AFX’s frequency response is only 90Hz to 20kHz. The reason for this is that an Atmos-enabled speaker doesn’t have to cover the vast frequency range of a typical speaker. The Motion AFX is far smaller than typical bookshelf speakers. The front is completely blocked off and no sound can escape directly toward the listener. Even though there’s a perforated grille at the front, the speaker has no front-facing driver. If you shine a flashlight through the Motion AFX’s grille, you’ll see the drivers on the top of the speaker against an angled ramp. The Motion AFX’s top has a perforated grille that hides the angled drivers. When source material containing height information is played, the Motion AFX projects that audio signal towards the ceiling. The Motion AFX’s drivers, comprised of a 0.75-inch aluminum dome tweeter and a 5.25-inch polypropylene cone bass/midbass driver with a stamped steel basket, are angled upward within the speaker cabinet. For that effect to happen, an Atmos-enabled speaker like the MartinLogan Motion AFX must point at your ceiling.
0 Comments
Leave a Reply. |
Details
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |